16T Front sprocket - 2017+ Kawasaki Z650 Forum
 1Likes
  • 1 Post By Shamsul Kamal
 
LinkBack Thread Tools
post #1 of 5 (permalink) Old 11-23-2017, 09:58 PM Thread Starter
Senior Member
 
Join Date: May 2017
Posts: 134
16T Front sprocket

Z650 front sprocket is 15T. I am thinking of buying a 16T front sprocket for easier cruising on highway. I am wondering if it can fit since 16T sprocket is a bit bigger.
Shamsul Kamal is offline  
Sponsored Links
Advertisement
 
post #2 of 5 (permalink) Old 11-28-2017, 02:42 AM Thread Starter
Senior Member
 
Join Date: May 2017
Posts: 134
I have installed 43T rear sprocket instead of changing the front sprocket.

So far so good, I like the new gear ratio setup.
Attached Thumbnails
Click image for larger version

Name:	43T vs stock.png
Views:	229
Size:	126.5 KB
ID:	3002  
crimsonxholic likes this.

Last edited by Shamsul Kamal; 11-28-2017 at 02:47 AM. Reason: wording changes
Shamsul Kamal is offline  
post #3 of 5 (permalink) Old 05-27-2018, 03:12 AM
Junior Member
 
Join Date: May 2018
Posts: 4
This response is late to the original date of the post, but for those who are reading this anyways:

I installed a 16 tooth counter shaft sprocket on a 2017 Z650. While the sprocket will fit, it did cause the chain to make very slight contact with the engine chain guard lip occasionally. Especially when chopping the throttle and the chain slaps from being driven from the engine to the wheel (and this was after adjusting chain slack tighter and looser than I'd normally run it). You will have better success getting the same amount of gearing alteration of a 16T countershaft sprocket by going to a 43T rear wheel sprocket. It is what I am currently using. Changes are, roughly speaking, 400 rpm reduction in top gear at same speed. There has been a slight improvement in fuel economy. For the argument that you could lose bottom end torque and acceleration; true. But I don't feel that loss, and not so much that it dismisses the advantage I feel in having a bike rev just a little lower at the same highway speeds I was running before. Generally, I now keep the bike running one gear lower than before for most sub-70mph speeds, but I like having a lower 6th gear ratio to handle 75-85 mph speeds a little calmer. Incidentally, if cruising at 75mph without undue load (like going up a grade or into a strong headwind), the little "eco" icon will stay on at 75mph. Prior to the gearing change, it would rarely do that.

I do wish the 16T could have worked without any clearance issues, as removing and installing a countershaft sprocket is far easier that swapping out a rear sprocket. I used an impact driver to remove the countershaft sprocket. You might be able to get away with using a pry bar. I set my torque for the countershaft sprocket at 92 ft/lbs. For those who do want to change out the countershaft sprocket, you could get away with reusing the countershaft sprocket washer, but I'd recommend replacing it if you do replace that sprocket (for a smaller one for those who want MORE torque or acceleration).
edmoto is offline  
Sponsored Links
Advertisement
 
post #4 of 5 (permalink) Old 05-27-2018, 11:05 AM
Junior Member
 
Join Date: May 2018
Posts: 4
To help picture what I described...

For reference, what is in the photos now is the original OEM 15T countershaft sprocket.

Pic1: There is a small gouge in the engine chain guard lip from when the 16T sprocket was used, showing where the outer edge of the chain roller plate hit the guard. I changed back to the 15T sprocket because on decel I could hear the "tick tick tick" of the chain just barely hitting the guard. I believe as the chain slack would grow over time this minor gouging could increase.

Pic2: 43T rear sprocket looks fine (to me) on the bike, and if you look at the chain adjustment index marks on the swingarm, I only had to move the rear axle back a little less than 1/2 inch. I don't feel any difference in turning and leans, and I still have adjustment left to account for roller pin wear on the chain over time. More importantly, I was able to use the stock OEM chain with the 43T rear sprocket, which meant no new chain (save $$$) and I didn't have to break the chain to shorten the link count.

Sorry if the pics are oversized to the forum screen space.
Attached Thumbnails
Click image for larger version

Name:	IMG_20180527_084450835.jpg
Views:	155
Size:	137.8 KB
ID:	4177   Click image for larger version

Name:	IMG_20180527_084716396_HDR.jpg
Views:	139
Size:	189.4 KB
ID:	4185  
edmoto is offline  
post #5 of 5 (permalink) Old 05-28-2018, 11:39 AM Thread Starter
Senior Member
 
Join Date: May 2017
Posts: 134
If I am not mistaken, I told the shop mechanic to cut the link to 112. Standard link is 114. This should give better chain wear according to gearing commander.
Shamsul Kamal is offline  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
Top Speed Run Kawasaki Z650 Stitch Kawasaki Z650 Pictures And Videos 22 07-08-2018 02:05 PM
Front flush mount turn signal options? tympyst Appearance Modifications 9 11-26-2017 09:17 PM
Front lights regulation OrtigoNover Kawasaki Z650 General Discussion 5 06-28-2017 11:00 AM
Front suspension really soft... czrlaker Suspension And Brakes 7 06-11-2017 02:56 PM
Front triple tree stand surprise JACoH Suspension And Brakes 1 05-13-2017 09:17 AM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome